1995 Chrysler Sebring Recalls

Description

VEHICLE DESCRIPTION: PASSENGER VEHICLES. IF THE RUBBER BOOTS ON THE LOWER LATERAL ARM BALL JOINTS OF THE FRONT SUSPENSION WERE DAMAGED DURING ASSEMBLY, DIRT AND WATER CAN INTRUDE. ALSO, MMC HAS ADDED THE POTENTIAL OF LEAKING MOISTURE, WHICH CAN CAUSE THE BALL STUD TO CORRODE.

Consequence

THIS CONDITION COULD CAUSE THE LOWER LATERAL ARM BALL JOINT TO SEPARATE, INCREASING THE RISK OF A VEHICLE CRASH. THIS CAMPAIGN SUPERCEDES MMC'S PREVIOUS SAFETY RECALL CAMPAIGN, SEE 99V-066.

Remedy

DEALERS WILL INSPECT THE LOWER LATERAL ARM BALL JOINT FOR WEAR. BALL JOINTS THAT EXHIBIT WEAR BEYOND THE ESTABLISHED TOLERANCE WILL BE REPLACED WITH NEWLY DESIGNED LATERAL ARM BALL JOINTS. BALL JOINTS THAT ARE WITHIN THE ESTABLISHED TOLERANCE WILL BE CLEANED AND A SPECIAL SEALANT WILL BE APPLIED TO PREVENT INTRUSION OF MOISTURE.

Manufacturer

DAIMLERCHRYSLER CORPORATION 967

Description

VEHICLE DESCRIPTION: PASSENGER VEHICLES. IF THE RUBBER BOOTS ON THE LOWER LATERAL ARM BALL JOINTS OF THE FRONT SUSPENSION WERE DAMAGED DURING ASSEMBLY, DIRT AND WATER CAN INTRUDE.

Consequence

THIS CONDITION COULD CAUSE THE LOWER LATERAL ARM BALL JOINT TO SEPARATE, INCREASING THE RISK OF A VEHICLE CRASH.

Remedy

DEALERS WILL INSPECT THE RUBBER BOOTS, AND IF THE BOOT IS DAMAGED, THEY WILL REPLACE THE LOWER LATERAL ARM AND BALL JOINT ON THE AFFECTED VEHICLES.

Manufacturer

DAIMLERCHRYSLER CORPORATION 827

Description

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LOWER CONTROL ARM BALL JOINT CAN SEPARATE DUE TO LOSS OF LUBRICATION.

Consequence

SEPARATION OF THE BALL JOINT COULD CAUSE A LOSS OF STEERING CONTROL INCREASING THE RISK OF A VEHICLE CRASH.

Remedy

DEALERS WILL INSPECT THE BALL JOINT END HOUSING COVER SEAL FOR LEAKAGE WITH A HIGH PRESSURE AIR TESTER AND THE RUBBER BOOT WILL BE VISUALLY INSPECTED FOR DAMAGE. IF THE COVER SEAL LEAKS OR THE BOOT IS DAMAGED, THE LOWER CONTROL ARM WILL BE REPLACED.

Manufacturer

CHRYSLER CORPORATION

Description

CERTAIN TIGAS FUEL PUMP MODULES MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006, SOLD UNDER VARIOUS BRAND NAMES AND P/NOS. THESE FUEL PUMP MODULES ARE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.

Consequence

FUEL RESTRICTION COULD RESULT IN LOSS OF POWER AND/OR ENGINE STALL, POSSIBLY RESULTING IN A VEHICLE CRASH.

Remedy

TI AUTOMOTIVE WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMP MODULES FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 6, 2006. OWNERS MAY CONTACT TI AUTOMOTIVE TOLL-FREE AT 1-877-461-1834.

Manufacturer

TI GROUP AUTOMOTIVE SYSTEMS, LLC

Description

CERTAIN AIRTEX FUEL PUMP MODULE ASSEMBLIES, P/N E7081H, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE VEHICLES LISTED ABOVE. THE WALL OF THE FLARED FITTING OF THE FUEL PUMP IS NOT THICK ENOUGH TO PREVENT THE MATING THREADED FITTINGS FROM BOTTOMING OUT BEFORE AN ADEQUATE SEAL IS ACHIEVED. THIS CONDITION MAY RESULT IN LEAKAGE OF FUEL AT THE CONNECTION OF THE VEHICLE FUEL LINE AND THE FUEL PUMP MODULE ASSEMBLY.

Consequence

IN THE PRESENCE OF AN IGNITION SOURCE, A FUEL LEAK COULD RESULT IN A FIRE.

Remedy

AIRTEX WILL NOTIFY OWNERS AND REPLACE THE FUEL PUMPS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING JULY 2007. OWNERS CAN CONTACT AIRTEX AUTOMOTIVE AT 800-880-3056.

Manufacturer

AIRTEX PRODUCTS FP072007-1