1997 Dodge Stratus Recalls

Description

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE SECONDARY HOOD LATCH SPRING CAN DISENGAGE FROM ITS RETENTION HOLE IF THE HOOD IS SLAMMED SHUT.

Consequence

IF THIS CONDITION OCCURS SIMULTANEOUSLY WITHOUT ENGAGING THE PRIMARY LATCH, THE HOOD WOULD NOT BE RESTRAINED INCREASING THE RISK OF A VEHICLE CRASH.

Remedy

DEALERS WILL REPLACE THE SECONDARY HOOD LATCH SPRING WITH A LONGER END HOOK SPRING.

Manufacturer

CHRYSLER CORPORATION

Description

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS. THE ADJUSTMENT OF THE CABLE CONNECTING THE CONSOLE SHIFTER MECHANISM TO THE IGNITION KEY CAN CAUSE A TRAPPED KEY CONDITION WHICH CAN RESULT IN A LOW FORCE REQUIRED TO DEPRESS THE SHIFT BUTTON. A COMBINATION OF APPLYING A MIS-ADJUSTED RELEASE BUTTON WITH A LOW FORCE ATTEMPT TO SHIFT OUT OF PARK WITH THE KEY IN THE LOCKED POSITION, CAN BREAK THE CONNECTING PIN IN THE SHIFTER.

Consequence

IF THIS HAPPENS, THE "IGNITION-PARK" INTERLOCK SYSTEM WILL BE NONFUNCTIONAL.

Remedy

DEALERS WILL INSPECT FOR PROPER OPERATION OF THE SYSTEM. ANY VEHICLES THAT ARE NOT FUNCTIONAL AFTER THE INSPECTION WILL HAVE THE SHIFT MECHANISM AND CABLE REPLACED WITH A "SELF-ADJUSTING" DESIGN.

Manufacturer

CHRYSLER CORPORATION

Description

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LOWER CONTROL ARM BALL JOINT CAN SEPARATE DUE TO LOSS OF LUBRICATION.

Consequence

SEPARATION OF THE BALL JOINT COULD CAUSE A LOSS OF STEERING CONTROL INCREASING THE RISK OF A VEHICLE CRASH.

Remedy

DEALERS WILL INSPECT THE BALL JOINT END HOUSING COVER SEAL FOR LEAKAGE WITH A HIGH PRESSURE AIR TESTER AND THE RUBBER BOOT WILL BE VISUALLY INSPECTED FOR DAMAGE. IF THE COVER SEAL LEAKS OR THE BOOT IS DAMAGED, THE LOWER CONTROL ARM WILL BE REPLACED.

Manufacturer

CHRYSLER CORPORATION

Description

ON CERTAIN PASSENGER VEHICLES, THE FLOOR SHIFTER IGNITION-PARK INTERLOCK MAY FAIL AND ALLOW THE SHIFTER TO BE MOVED OUT OF THE PARK POSITION WITH THE KEY REMOVED. AN INOPERATIVE INTERLOCK MAY ALSO ALLOW THE KEY TO BE REMOVED WHEN THE SHIFTER HAS NOT BEEN PLACED IN THE PARK POSITION.

Consequence

EITHER CIRCUMSTANCE MAY RESULT IN THE VEHICLE ROLLING AWAY WITHOUT WARNING.

Remedy

DEALERS WILL INSTALL A NEW LOAD-LIMITING PUSH ROD INTO THE FLOOR SHIFTER LEVER OF THE AFFECTED VEHICLES. OWNER NOTIFICATION BEGAN ON JUNE 14, 2004. OWNERS SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.

Manufacturer

DAIMLERCHRYSLER CORPORATION C45

Description

CERTAIN TIGAS FUEL PUMP MODULES MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006, SOLD UNDER VARIOUS BRAND NAMES AND P/NOS. THESE FUEL PUMP MODULES ARE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.

Consequence

FUEL RESTRICTION COULD RESULT IN LOSS OF POWER AND/OR ENGINE STALL, POSSIBLY RESULTING IN A VEHICLE CRASH.

Remedy

TI AUTOMOTIVE WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMP MODULES FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 6, 2006. OWNERS MAY CONTACT TI AUTOMOTIVE TOLL-FREE AT 1-877-461-1834.

Manufacturer

TI GROUP AUTOMOTIVE SYSTEMS, LLC

Description

QUALIS AUTOMOTIVE IS RECALLING CERTAIN AFTERMARKET BALL JOINTS SOLD FOR USE ON CERTAIN PASSENGER VEHICLES. THE SOCKET MAY HAVE BEEN EXCESSIVELY HARDENED WHICH COULD CAUSE IT TO CRACK NEAR THE RETAINING RING GROOVE ALLOWING THE BALL STUD TO SEPARATE UNDER IMPACT LOAD. THE SUBJECT BALL JOINTS WERE SOLD AS FOUR PART NUMBERS, D10945, D10946, G10945, AND G10946. THE AFFECTED CONTROL ARMS, D10945 AND D10946, ARE STAMPED WITH THE FOLLOWING DATES ON THE BALL JOINTS: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, AND 116609. THE G10945 AND G10946 ARE THE SAME PART AS THE D10945 AND D10946 RESPECTIVELY. THEY ARE LABELED DIFFERENTLY DEPENDING ON THE AFTERMARKET CUSTOMER.

Consequence

SEPARATION OF THE BALL STUD FROM THE SOCKET OF THE BALL JOINT HOUSING WOULD ALLOW THE CONTROL ARM TO COLLAPSE AND THE WHEEL TO FOLD IN CAUSING LOSS OF STEERING CONTROL, POSSIBLY RESULTING IN A CRASH.

Remedy

QUALIS AUTOMOTIVE WILL REPLACE THE BALL JOINTS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 9, 2009. OWNERS MAY CONTACT QUALIS AUTOMOTIVE AT 1-800-493-4128.

Manufacturer

QUALIS AUTOMOTIVE LLC

Description

FEDERAL-MOGUL IS RECALLING CERTAIN REPLACEMENT CONTROL ARM ASSEMBLIES, PART NUMBERS K7425, 10945, FA4510X, K7427, 10946, AND FA4611X, SOLD FOR USE ON VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE BALL JOINT ON THE CONTROL ARM ASSEMBLY CAN FAIL CAUSING THE BALL STUD TO WEAR THROUGH THE CONTROL ARM HOUSING RESULTING IN NOISE AND/OR SEPARATION OF THE BALL STUD FROM THE HOUSING.

Consequence

IF THERE IS A SEPARATION OF THE BALL STUD FROM THE HOUSING, THE DRIVER CAN LOOSE STEERING CONTROL, POSSIBLY RESULTING IN A VEHICLE CRASH.

Remedy

FEDERAL-MOGUL WILL NOTIFY OWNERS OF RECORD AND REPLACE THE AFFECTED CONTROL ARMS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 28, 2011. OWNERS MAY CONTACT FEDERAL-MOGUL AT 1-877-489-6659.

Manufacturer

FEDERAL-MOGUL CORPORATION